TECHSHIP IS A GLOBAL SUPPLIER OF WIRELESS COMPONENTS
GM500 U1A M.2Supplier number:
Welink GM500 U1A M.2 (US) is a LTE CAT-4 module with download speeds of up to 150Mbps and upload speed of up to 50Mbps. It is fully backward compatible with existing 3G networks.
A rich set of internet protocols (PAP and CHAP used for PPP connections) and abundant functions (GNSS, Remote wakeup, MMS, SMS,FOTA) extend the applicability of the module to a wide range of M2M applications. ME3630 PCIE can be widely used in M2M industries such as smart meter, Security and monitor, Industrial router, DTU, CPE, Telematics etc.
This document is the Product Technical Specification for the GM500 GSM/WCDMA/LTE-FDD module. It defines the high level product features and illustrates the interface for these features. This document is intended to cover the hardware aspects of the product, including electrical and mechanical.
This document is aimed at providing a detailed specification and a comprehensive listing as a reference for the whole set of AT commands for the GM500.
What Linux kernel modules and configs are commonly used for communicating with cellular modules over their USB interface?
Most cellular modules can be supported in Linux by using som of the in-kernel drivers. The physical data interface to the host Linux system is usually done over USB which enumerates a set of different endpoints/interfaces. A set of serial interfaces for Modem/PPP, AT commands, NMEA location data and chipset debug information are almost always available in all configurations.
In addition some type of network endpoint/interface are also available and exposed. This can vary between manufacturers and chipset vendors and can also commonly be configurable by using USB configuration mode switching or through vendor specific AT commands.
Recommended kernel configurations to enable are listed bellow. Many cellular modules base their Linux support on these modules and drivers. Once included in the kernel build, the USB interfaces will be detected and bound correctly out-of-the-box or after applying source code patches to the driver modules.
Configs for USB serial drivers:
Configs for Modem/PPP support:
Configs for USB network drivers:
Please relate to the Techship product specific web pages for vendor specific Linux integration guides.
Below is a selection of kernel commits relating to cellular module support in Linux kernels:
qmi_wwan: Add support for Fibocom NL678 series
qmi_wwan: Added support for Telit LN940 series
qmi_wwan: Added support for Fibocom NL668 series
USB: serial: option: add support for GosunCn ME3630 RNDIS mode
USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode
USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode)
USB: serial: option: add Fibocom NL678 series
USB: serial: option: add Telit LN940 series
USB: serial: option: add Fibocom NL668 series
USB: serial: option: add GosunCn ZTE WeLink ME3630
qmi_wwan: apply SET_DTR quirk to the SIMCOM shared device ID
If you use any of the listed cellular modules, drivers and specified USB modes in the commits above, ensure that your kernel version already include the patch or apply it to your build.
Technology / Antenna Frequency: GSM 850/900/1800/1900, UMTS 2100, LTE 698-960/1710-2170/2500-2700 MHz | Mounting method: Adhesive | Antenna Location: External | VSWR: 3 :1 | Gain: 2.14 dBi | Connector Type: SMA-M | Impedance: 50 Ohm | Cable length: 30 cm | Cable Specification: RG174 | Polarization: Linear | Max power: 35 W | Operating Temperature Range: -40 °C – 85 °C | Width: 60 mm | Length: 112.5 mm | Height: 11.3 mm
1 PCS PRICE $6.80